MKP336 2 X2
www.vishay.com Vishay BCcomponents
Not Recommended for New Designs, Use MKP339 X2
Revision: 12-Sep-17 1Document Number: 28120
For technical questions, contact: rfi@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Interference Suppression Film Capacitors - Class X2
Radial MKP 310 VAC - Standard Across the Line
FEATURES
• 10 mm to 27.5 mm lead pitch
• Supplied loose in box, taped on reel
• Material categorization:
for definitions of compliance please see
www.vishay.com/doc?99912
APPLICATIONS
For standard across the line X2 applications
See also application note: www.vishay.com/doc?28153
Note
•For more detailed data and test requirements, contact: rfi@vishay.com
QUICK REFERENCE DATA
Capacitance range (E12 series) 0.001 µF to 2.2 µF (preferred values acc. to E6)
Capacitance tolerance ± 20 %; ± 10 %; ± 5 %
Climatic testing class according to IEC 60068-1 55/110/56/B
Rated AC voltage 310 VAC; 50 Hz to 60 Hz
Permissible DC voltage 800 VDC at 85 °C, 630 VDC at 110 °C
Maximum application temperature C 470 nF: 110 °C (125 °C for less than 1000 h), C > 470 nF: 110 °C
Reference standards
IEC 60384-14 ed-4 (2013) and EN 60384-14
IEC 60065, pass. flamm. class B for volumes > 1750 mm3
CQC GB/T6346.14-2015
UL 60384-14; CSA E384-14
Dielectric Polypropylene film
Electrodes Metallized film
Construction
Mono construction
Encapsulation Plastic case, epoxy resin sealed, flame retardant UL-class 94 V-0
Leads Tinned wire
Marking
C-value; tolerance; rated voltage; sub-class; manufacturer’s type designation;
code for dielectric material; manufacturer location; manufacturer’s logo;
year and week; safety approvals
DIMENSIONS in millimeters
h
lt
lw
Ø dt
P ± 0.4
MKP336 2 X2
www.vishay.com Vishay BCcomponents
Not Recommended for New Designs, Use MKP339 X2
Revision: 12-Sep-17 2Document Number: 28120
For technical questions, contact: rfi@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
COMPOSITION OF CATALOG NUMBER
Notes
(1) For detailed tape specifications refer to packaging information: www.vishay.com/doc?28139
(2) Taped on reel pitch = 27.5 mm is not available
BFC2 336 2X XX X
2222(*) 336 2X XX X
(*) old ordering code
REBMUN EDOC.LOT-CSNOISNEMID DRADNATSGNIGAKCAPEPYT
336 2
X2
Loose in box
Lead length 3.5 mm + 1 mm/- 0.5 mm or 3.5 mm ± 0.3 mm
± 20 %
BFC2 336 20…
Lead length 5.0 mm ± 1.0 mm See tables
Lead length 25.0 mm ± 2.0 mm BFC2 336 26…
Taped on reel
(1)
H = 18.5 mm; P
0
=
12.7 mm BFC2 336 23…
Loose in box
Lead length 3.5 mm + 1 mm/- 0.5 mm or 3.5 mm ± 0.3 mm
± 10 %
BFC2 336 21…
selbat eeSmm 0.1 ± mm 0.5 htgnel daeL
…72 633 2CFBmm 0.2 ± mm 0.52 htgnel daeL
Taped on reel
(1)
H = 18.5 mm; P
0
= 12.7 mm BFC2 336 24…
Loose in box
Lead length 3.5 mm + 1 mm/- 0.5 mm or 3.5 mm ± 0.3 mm
± 5 %
BFC2 336 22…
selbat eeSmm 0.1 ± mm 0.5 htgnel daeL
…82 633 2CFBmm 0.2 ± mm 0.52 htgnel daeL
Taped on reel
(1)
H = 18.5 mm; P
0
= 12.7 mm BFC2 336 25…
PACKAGING ALTERNATIVE LARGER PITCH SIZES C-TOL. CODE NUMBER
Loose in box
Lead length 3.5 mm + 1 mm/- 0.5 mm or 3.5 mm ± 0.3 mm
± 20 %
See tables for details
Lead length 5.0 mm ± 1.0 mm
Lead length 25.0 mm ± 2.0 mm
Taped on reel
(1)
H = 18.5 mm; P
0
= 12.7 mm
Loose in box
Lead length 3.5 mm + 1 mm/- 0.5 mm or 3.5 mm ± 0.3 mm
± 10 %
Lead length 5.0 mm ± 1.0 mm
Lead length 25.0 mm ± 2.0 mm
Taped on reel
(1)(2)
H = 18.5 mm P
0
= 12.7 mm
TYPE AND PITCHES
336 2
X2
10.0 mm
15.0 mm
22.5 mm
27.5 mm
CAPACITANCE
(numerically)
Example:
104 = 10 x 10 = 100 nF
MULTIPLIER
(nF)
0.1 2
13
10 4
100 5
MKP336 2 X2
www.vishay.com Vishay BCcomponents
Not Recommended for New Designs, Use MKP339 X2
Revision: 12-Sep-17 3Document Number: 28120
For technical questions, contact: rfi@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Note
(1) See “Voltage Proof Test for Metalized Film Capacitors”: www.vishay.com/doc?28169
SPECIFIC REFERENCE DATA
DESCRIPTION VALUE
Rated AC voltage URAC 310 V
Permissible DC voltage URDC 630 V
Tangent of loss angle: at 1 kHz at 10 kHz
C < 470 nF 10 x 10-4 20 x 10-4
470 nF C 1 µF 20 x 10-4 70 x 10-4
C > 1 µF 30 x 10-4 -
Rated voltage pulse slope (dU/dt)R at 435 VDC -
Pitch = 10 mm 600 V/µs
Pitch = 15 mm and 7.5 mm (bent back) 400 V/µs
Pitch = 22.5 mm 150 V/µs
Pitch = 27.5 mm 100 V/µs
R between leads, for C 0.33 µF at 100 V; 1 min > 15 000 M
RC between leads, for C > 0.33 µF at 100 V; 1 min > 5000 s
R between leads and case; 100 V; 1 min > 30 000 M
Withstanding (DC) voltage (cut off current 10 mA) (1); rise time 1000 V/s:
C 1 µF 2200 V; 1 min
C > 1 µF 1800 V; 1 min
Withstanding (AC) voltage between leads and case 2120 V; 1 min
Max. application temperature for 0.001 µF C 0.47 µF 110 °C (125 °C for less than 1000 h)
Max. application temperature for C > 0.47 µF 110 °C
ELECTRICAL DATA AND ORDERING CODE - PITCH 10 mm
URAC
(V)
CAP.
(μF)
DIMENSIONS
w x h x l
(mm)
MASS
(g) (3)
CATALOG NUMBER BFC2 336 ..... AND PACKAGING
LOOSE IN BOX REEL (500 mm) (1)(2)
SHORT LEADS LONG LEADS H = 18.5 mm
P0 = 12.7 mm
lt = 3.5 mm
+ 1 mm/- 0.5 mm
lt = 5.0 mm
± 1.0 mm SPQ lt = 25.0 mm
± 2.0 mm SPQ SPQ
310
PITCH = 10.0 mm ± 0.4 mm; dt = 0.6 mm ± 0.06 mm; C-TOL. = ± 20 %
0.0010
4.0 x 10.0 x 12.5 0.6
20102 29131
1000
26102
1250
23102
14000.0015 20152 29132 26152 23152
0.0022 20222 29133 26222 23222
0.0033 20332 29134 26332
1000
23332
1100
0.0047 20472 29135 26472 23472
0.0068 20682 29136 26682 23682
0.010 20103 29137 26103 23103
0.015 20153 29138 26153 23153
0.022 20223 29139 26223 23223
0.033 20333 29141 750 26333 750 23333 900
PITCH = 10.0 mm ± 0.4 mm; dt = 0.6 mm ± 0.06 mm; C-TOL. = ± 10 %
0.0010
4.0 x 10.0 x 12.5 0.6
21102 29154
1000
27102
1250
24102
1400
0.0012 21122 - 27122 24122
0.0015 21152 29155 27152 24152
0.0018 21182 - 27182 24182
0.0022 21222 29156 27222 24222
MKP336 2 X2
www.vishay.com Vishay BCcomponents
Not Recommended for New Designs, Use MKP339 X2
Revision: 12-Sep-17 4Document Number: 28120
For technical questions, contact: rfi@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Notes
• SPQ = Standard Packing Quantity
(1) H = In-tape height; P0 = sprocket hole distance; for detailed specifications refer to packaging information: www.vishay.com/doc?28139
(2) Reel diameter = 356 mm is available on request
(3) Weight for short lead product only
310
PITCH = 10.0 mm ± 0.4 mm; dt = 0.6 mm ± 0.06 mm; C-TOL. = ± 10 %
0.0027
4.0 x 10.0 x 12.5 0.6
21272 -
1000
27272
1000
24272
1100
0.0033 21332 29157 27332 24332
0.0039 21392 - 27392 24392
0.0047 21472 29158 27472 24472
0.0056 21562 - 27562 24562
0.0068 21682 29159 27682 24682
0.0082 21822 - 27822 24822
0.010 21103 29161 27103 24103
0.012 21123 - 27123 24123
0.015 21153 29162 27153 24153
0.018 21183 - 27183 24183
0.022 21223 29163 27223 24223
0.027 21273 - 750 27273 750 24273 900
0.033 21333 29164 27333 24333
PITCH = 10.0 mm ± 0.4 mm; dt = 0.6 mm ± 0.06 mm; C-TOL. = ± 5 %
0.0010
4.0 x 10.0 x 12.5 0.6
22102 -
1000
28102
1250
25102
1400
0.0012 22122 - 28122 25122
0.0015 22152 - 28152 25152
0.0018 22182 - 28182 25182
0.0022 22222 - 28222 25222
0.0027 22272 - 28272
1000
25272
1100
0.0033 22332 - 28332 25332
0.0039 22392 - 28392 25392
0.0047 22472 - 28472 25472
0.0056 22562 - 28562 25562
0.0068 22682 - 28682 25682
0.0082 22822 - 28822 25822
0.010 22103 - 28103 25103
0.012 22123 - 28123 25123
0.015 22153 - 28153 25153
0.018 22183 - 28183 25183
0.022 22223 - 28223 25223
0.027 22273 - 750 28273 750 25273 900
0.033 22333 - 28333 25333
ELECTRICAL DATA AND ORDERING CODE - PITCH 10 mm
URAC
(V)
CAP.
(μF)
DIMENSIONS
w x h x l
(mm)
MASS
(g) (3)
CATALOG NUMBER BFC2 336 ..... AND PACKAGING
LOOSE IN BOX REEL (500 mm) (1)(2)
SHORT LEADS LONG LEADS H = 18.5 mm
P0 = 12.7 mm
lt = 3.5 mm
+ 1 mm/- 0.5 mm
lt = 5.0 mm
± 1.0 mm SPQ lt = 25.0 mm
± 2.0 mm SPQ SPQ
MKP336 2 X2
www.vishay.com Vishay BCcomponents
Not Recommended for New Designs, Use MKP339 X2
Revision: 12-Sep-17 5Document Number: 28120
For technical questions, contact: rfi@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Notes
• SPQ = Standard Packing Quantity
(1) H = In-tape height; P0 = sprocket hole distance; for detailed specifications refer to packaging information: www.vishay.com/doc?28139
(2) Reel diameter = 356 mm is available on request
(3) Weight for short lead product only
ELECTRICAL DATA AND ORDERING CODE - PITCH 15 mm
URAC
(V) CAP.
(μF)
DIMENSIONS
w x h x l
(mm)
MASS
(g) (3)
CATALOG NUMBER BFC2 336 ..... AND PACKAGING
LOOSE IN BOX REEL (500 mm) (1)(2)
SHORT LEADS LONG LEADS H = 18.5 mm
P0 = 12.7 mm
lt = 3.5 mm
± 0.3 mm
lt = 5.0 mm
± 1.0 mm SPQ lt = 25.0 mm
± 2.0 mm SPQ SPQ
310
PITCH = 15 mm ± 0.4 mm; dt = 0.60 ± 0.06 mm; C-TOL. = ± 20 %
0.010
5.0 x 11.0 x 17.5 0.98
29001 29273
1000
29097
1000
29004
1100
0.015 29011 29274 29071 29014
0.022 29021 29275 29076 29024
0.033 29031 29276 29082 29034
0.047 20473 29142 26473 23473
0.068 20683 29143 26683 23683
0.10 20104 29144 26104 23104 900
0.15 6.0 x 12.0 x 17.5 1.4 20154 29145 26154 500 23154 650
PITCH = 15 mm ± 0.4 mm; dt = 0.80 ± 0.08 mm; C-TOL. = ± 20 %
0.22 7.0 x 13.5 x 17.5 1.8 20224 29146 500 26224 500 23224 600
PITCH = 15 mm ± 0.4 mm; dt = 0.60 ± 0.06 mm; C-TOL. = ± 10 %
0.010
5.0 x 11.0 x 17.5 0.98
29002 29281
1000
29066
1000
29005
1100
0.012 29007 - 29068 29009
0.015 29012 29282 29072 29015
0.018 29017 - 29074 29019
0.022 29022 29283 29077 29025
0.027 29027 - 29079 29029
0.033 29032 29284 29083 29035
0.039 21393 - 27393 24393
0.047 21473 29165 27473 24473
0.056 21563 - 27563 24563
0.068 21683 29166 27683 24683 900
0.082 21823 - 27823 24823
0.10 21104 29167 27104
500
24104 800
0.12 6.0 x 12.0 x 17.5 1.4 21124 - 27124 24124 650
0.15 21154 29168 27154 24154
PITCH = 15 mm ± 0.4 mm; dt = 0.80 ± 0.08 mm; C-TOL. = ± 10 %
0.18 7.0 x 13.5 x 17.5 1.8 21184 - 500 27184 500 24184 600
0.22 21224 29169 27224 24224
PITCH = 15 mm ± 0.4 mm; dt = 0.60 ± 0.06 mm; C-TOL. = ± 5 %
0.010
5.0 x 11.0 x 17.5 0.98
29003 -
1000
29067
1000
29006
1100
0.012 29008 - 29069 29061
0.015 29013 - 29073 29016
0.018 29018 - 29075 29062
0.022 29023 - 29078 29026
0.027 29028 - 29081 29063
0.033 29033 - 29084 29036
0.039 22393 - 28393 25393
0.047 22473 - 28473 25473
0.056 22563 - 28563 25563
0.068 22683 - 28683 25683 900
0.082 22823 - 28823 25823
0.10 22104 - 28104
500
25104 800
0.12 6.0 x 12.0 x 17.5 1.4 22124 - 28124 25124 650
0.15 22154 - 28154 25154
PITCH = 15 mm ± 0.4 mm; dt = 0.80 ± 0.08 mm; C-TOL. = ± 5 %
0.18 7.0 x 13.5 x 17.5 1.8 22184 - 500 28184 500 25184 600
MKP336 2 X2
www.vishay.com Vishay BCcomponents
Not Recommended for New Designs, Use MKP339 X2
Revision: 12-Sep-17 6Document Number: 28120
For technical questions, contact: rfi@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Notes
• SPQ = Standard Packing Quantity
(1) H = In-tape height; P0 = sprocket hole distance; for detailed specifications refer to packaging information: www.vishay.com/doc?28139
(2) Reel diameter = 356 mm is available on request
(3) Weight for short lead product only
ELECTRICAL DATA AND ORDERING CODE - PITCH 22.5 mm
URAC
(V)
CAP.
(μF)
DIMENSIONS
w x h x l
(mm)
MASS
(g) (3)
CATALOG NUMBER BFC2 336 ..... AND PACKAGING
LOOSE IN BOX REEL (500 mm) (1)(2)
SHORT LEADS LONG LEADS H = 18.5 mm
P0 = 12.7 mm
lt = 3.5 mm
± 0.3 mm
lt = 5.0 mm
± 1.0 mm SPQ lt = 25.0 mm
± 2.0 mm SPQ SPQ
310
PITCH = 22.5 mm ± 0.4 mm; dt = 0.80 mm ± 0.08 mm; C-TOL. = ± 20 %
0.15
6.0 x 15.5 x 26.0 2.4
29041 29277
300
29087
500
29044 600
0.22 29051 29278 29093 29053 550
0.33 20334 29147 26334 23334 450
0.47 7.0 x 16.5 x 26.0 2.9 20474 29148 200 26474 500 23474 400
PITCH = 22.5 mm ± 0.4 mm; dt = 0.80 mm ± 0.08 mm; C-TOL. = ± 10 %
0.12
6.0 x 15.5 x 26.0 2.4
29037 -
300
29085
500
29039 600
0.15 29042 29285 29088 29045
0.18 29047 - 29091 29049 550
0.22 29052 29286 29094 29054
0.27 21274 - 27274 24274 450
0.33 21334 29171 27334 24334
0.39 7.0 x 16.5 x 26.0 2.9 21394 - 200 27394 24394 400
0.47 21474 29172 27474 24474
PITCH = 22.5 mm ± 0.4 mm; dt = 0.80 mm ± 0.08 mm; C-TOL. = ± 5 %
0.12
6.0 x 15.5 x 26.0 2.4
29038 -
300
29086
500
29064 600
0.15 29043 - 29089 29046
0.18 29048 - 29092 29065 550
0.22 22224 - 28224 25224
0.27 22274 - 28274 25274 450
0.33 7.0 x 16.5 x 26.0 2.9 22334 - 200 28334 25334
0.39 22394 - 28394 25394 400
MKP336 2 X2
www.vishay.com Vishay BCcomponents
Not Recommended for New Designs, Use MKP339 X2
Revision: 12-Sep-17 7Document Number: 28120
For technical questions, contact: rfi@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Notes
• SPQ = Standard Packing Quantity
(1) Weight for short lead product only
ELECTRICAL DATA AND ORDERING CODE - PITCH 27.5 mm
URAC
(V)
CAP.
(μF)
DIMENSIONS
w x h x l
(mm)
MASS
(g) (1)
CATALOG NUMBER BFC2 336 ..... AND PACKAGING
LOOSE IN BOX
SHORT LEADS LONG LEADS
lt = 3.5 mm
± 0.3 mm
lt = 5.0 mm
± 1.0 mm SPQ lt = 25.0 mm
± 2.0 mm SPQ
310
PITCH = 27.5 mm ± 0.4 mm; dt = 0.80 mm ± 0.08 mm; C-TOL. = ± 20 %
0.47 9.0 x 19.0 x 31.5 5.5 29055 29279
100
29095 150
0.68 20684 29149 26684
1251.0 11.0 x 21.0 x 31.0 7.4 20105 29151 26105
1.5 13.0 x 23.0 x 31.0 9.2 20155 29152 26155
2.2 15.0 x 25.0 x 31.5 12.3 20225 29153 26225 75
PITCH = 27.5 mm ± 0.4 mm; dt = 0.80 mm ± 0.08 mm; C-TOL. = ± 10 %
0.47
9.0 x 19.0 x 31.5 5.5
29056 29287
100
29096 150
0.56 21564 - 27564
125
0.68 21684 29173 27684
0.82 11.0 x 21.0 x 31.0 7.4 21824 - 27824
1.0 21105 29174 27105
1.2 13.0 x 23.0 x 31.0 9.2 21125 - 27125
1.5 21155 29175 27155
1.8 15.0 x 25.0 x 31.5 12.3 21185 - 27185 75
2.2 21225 29176 27225
PITCH = 27.5 mm ± 0.4 mm; dt = 0.80 mm ± 0.08 mm; C-TOL. = ± 5 %
0.47
9.0 x 19.0 x 31.5 5.5
22474 -
100
28474
125
0.56 22564 - 28564
0.68 22684 - 28684
0.82 11.0 x 21.0 x 31.0 7.4 22824 - 28824
1.0 22105 - 28105
1.2 13.0 x 23.0 x 31.0 9.2 22125 - 28125
1.5 22155 - 28155
1.8 15.0 x 25.0 x 31.5 12.3 22185 - 28185 75
2.2 22225 - 28225
MKP336 2 X2
www.vishay.com Vishay BCcomponents
Not Recommended for New Designs, Use MKP339 X2
Revision: 12-Sep-17 8Document Number: 28120
For technical questions, contact: rfi@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MOUNTING
Normal Use
The capacitors are designed for mounting on printed-circuit boards. The capacitors packed in bandoliers are designed for
mounting in pinted-circuit boards by means of automatic insertion machines.
For detailed tape specifications refer to packaging information: www.vishay.com/doc?28139
Specific Method of Mounting to Withstand Vibration and Shock
In order to withstand vibration and shock tests, it must be insured that the stand-off pips are in good contact with the printed
circuit board:
• For pitches 15 mm capacitors shall be mechanically fixed by the leads
• For larger pitches the capacitors shall be mounted in the same way and the body clamped.
Space Requirements on Printed Circuit Board
The maximum space for length (Imax.), width (wmax.) and height (hmax.) of film capacitors to take in account on the printed circuit
board is shown in the drawings.
• For products with pitch 15 mm, w = l = 0.3 mm; h = 0.1 mm
• For products with 15 mm < pitch 27.5 mm, w = l = 0.5 mm; h = 0.1 mm
Eccentricity defined as in drawing. The maximum eccentricity is smaller than or equal to the lead diameter of the product
concerned.
SOLDERING CONDITIONS
For general soldering conditions and wave soldering profile, we refer to the application note:
“Soldering Guidelines for Film Capacitors”: www.vishay.com/doc?28171
Storage Temperature
Tstg = -25 °C to +35 °C with RH maximum 75 % without condensation
Ratings and Characteristics Reference Conditions
Unless otherwise specified, all electrical values apply to an ambient temperature of 23 °C ± 1 °C, an atmospheric pressure of
86 kPa to 106 kPa and a relative humidity of 50 % ± 2 %.
For reference testing, a conditioning period shall be applied over 96 h ± 4 h by heating the products in a circulating air oven at
the rated temperature and a relative humidity not exceeding 20 %.
APPROVALS
SAFETY APPROVALS X2 VOLTAGE VALUE FILE NUMBERS LINK
EN 60384-14 (ENEC)
(= IEC 60384-14 ed-4 (2013)) 310 VAC 1 nF to 2.2 µF FI 2016052 www.vishay.com/doc?28179
UL 60384-14 310 VAC 1 nF to 2.2 µF E354331 www.vishay.com/doc?28184
CSA-E 384-14 310 VAC 1 nF to 2.2 µF E354331
CQC GB/T6346.14-2015 310 VAC 1 nF to 2.2 µF CQC07001021280 (L) www.vishay.com/doc?28199
CQC04001009262 (F) www.vishay.com/doc?28200
CB test certificate 310 VAC 1 nF to 2.2 µF FI 9369 www.vishay.com/doc?28175
The ENEC-approval together with the CB-certificate replace all national marks of the following countries (they have already signed the
ENEC-agreement): Austria; Belgium; Czech. Republic; Denmark; Finland; France; Germany; Greece; Hungary; Ireland; Italy; Luxembourg;
Netherlands; Norway; Portugal; Slovenian; Spain; Sweden; Switzerland and United Kingdom.
CBA116
Eccentricity
w
max.
= W + Δ
h
max.
= h + Δ
I
max.
= I + Δ
Seating plane
MKP336 2 X2
www.vishay.com Vishay BCcomponents
Not Recommended for New Designs, Use MKP339 X2
Revision: 12-Sep-17 9Document Number: 28120
For technical questions, contact: rfi@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CHARACTERISTICS
Capacitance as a function of ambient temperature
(typical curve)
Tangent of loss angle as a function of frequency
(typical curve)
Max. RMS voltage as a function of frequency
(typical curve)
Impedance as a function of frequency
(typical curve)
Resonant frequency as a function of capacitance
(typical curve)
Max. RMS current as a function of frequency
(typical curve)
typical
- 50
ΔC/C
(%)
2
- 2
- 4
- 6
0
050100Tamb (°C)
4
min.
max.
Dissipation
factor (x 10-4)
C > 1 µF
C ≤ 10 nF
10 nF < C ≤ 47 nF
47 nF < C ≤ 220 nF
220 nF < C ≤ 1 µF
103
102
101
100
101102103104105
f (Hz)
Tamb ≤ 110 °C
AC voltage
(V)
103
10 2
10 1
f (Hz)
10110 2103104105
10 nF
47 nF
100 nF
470 nF
1000 nF
4.7 nF
1 nF
Impedance
(Ω)
10
3
10
1
10
-2
10
0
f (Hz)
10
6
10
4
10
5
10
7
10
8
10
-1
X2
102
101
100
10-1
110
100 1000 10 000
f (MHz)
C (nF)
470 nF
100 nF
47 nF
10 nF
1000 nF
1nF
2200 nF
4.7 nF
AC current
(mA)
10
4
10
2
10
0
10
1
f (Hz)
10
1
10
2
10
3
10
4
10
5
10
-1
T
amb
≤
110 °C
MKP336 2 X2
www.vishay.com Vishay BCcomponents
Not Recommended for New Designs, Use MKP339 X2
Revision: 12-Sep-17 10 Document Number: 28120
For technical questions, contact: rfi@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Insulation resistance
APPLICATION NOTES
• For X2 electromagnetic interference suppression in standard across the line applications (50/60 Hz) with a maximum mains
voltage of 310 VAC.
• For series impedance applications we refer to the application note www.vishay.com/doc?28153
• For capacitors connected in parallel, normally the proof voltage and possibly the rated voltage must be reduced. For
information depending of the capacitance value and the number of parallel connections contact: rfi@vishay.com.
• These capacitors are not intended for continuous pulse applications. For these situations, capacitors of the AC and pulse
programs must be used.
• The maximum ambient temperature must not exceed 110 °C (125 °C for less than 1000 h) for C 470 nF and 110 °C for
C > 470 nF
• Rated voltage pulse slope:
If the pulse voltage is lower than the rated voltage, the values of the specific reference data can be multiplied by 435 VDC and
divided by the applied voltage
INSPECTION REQUIREMENTS
General Notes
Sub-clause numbers of tests and performance requirements refer to the “Sectional Specification, IEC Publication
IEC 60384-14 ed-4 (2013) and Specific Reference Data”.
GROUP C INSPECTION REQUIREMENTS
SUB-CLAUSE NUMBER AND TEST CONDITIONS PERFORMANCE REQUIREMENTS
SUB-GROUP C1A PART OF
SAMPLE OF SUB-GROUP C1
4.1 Dimensions (detail) As specified in chapters “General Data” of this
specification
Initial measurements Capacitance
Tangent of loss angle:
For C 1 µF at 10 kHz
For C > 1 µF at 1 kHz
4.3 Robustness of terminations Tensile: Load 10 N; 10 s
Bending: Load 5 N; 4 x 90°
No visible damage
4.4 Resistance to soldering heat No pre-drying
Method: 1A
Solder bath: 280 °C ± 5 °C
Duration: 10 s
106
105
104
020 40 60 80 100
Tamb (°C)
RC (s)
MKP336 2 X2
www.vishay.com Vishay BCcomponents
Not Recommended for New Designs, Use MKP339 X2
Revision: 12-Sep-17 11 Document Number: 28120
For technical questions, contact: rfi@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
SUB-GROUP C1A PART OF
SAMPLE OF SUB-GROUP C1
4.19 Component solvent resistance Isopropylalcohol at room temperature
Method: 2
Immersion time: 5 min ± 0.5 min
Recovery time:
Min. 1 h, max. 2 h
4.4.2 Final measurements Visual examination No visible damage
Legible marking
Capacitance |C/C| 5 % of the value measured initially
Tangent of loss angle Increase of tan :
0.008 for: C 1 µF or
0.005 for: C > 1 µF
Compared to values measured initially
Insulation resistance As specified in section “Insulation resistance”
of this specification
SUB-GROUP C1B PART OF
SAMPLE OF SUB-GROUP C1
Initial measurements Capacitance
Tangent of loss angle:
For C 1 µF at 10 kHz
For C > 1 µF at 1 kHz
4.20 Solvent resistance of the
marking: see section
“General notes”; item 5
Isopropylalcohol at room temperature
Method: 1
Rubbing material: Cotton wool
Immersion time: 5 min ± 0.5 min
No visible damage
Legible marking
4.6 Rapid change of temperature A = - 55 °C
B = + 110 °C
5 cycles
Duration t = 30 min
4.6.1 Inspection Visual examination No visible damage
4.7 Vibration Mounting: See section “Mounting” of this
specification
Procedure B4
Frequency range: 10 Hz to 55 Hz
Amplitude: 0.75 mm or
Acceleration 98 m/s
(whichever is less severe)
Total duration 6 h
4.7.2 Final inspection Visual examination No visible damage
4.9 Shock Mounting: See section “Mounting” for more
information
Pulse shape: Half sine
Acceleration: 490 m/s
Duration of pulse: 11 ms
GROUP C INSPECTION REQUIREMENTS
SUB-CLAUSE NUMBER AND TEST CONDITIONS PERFORMANCE REQUIREMENTS
MKP336 2 X2
www.vishay.com Vishay BCcomponents
Not Recommended for New Designs, Use MKP339 X2
Revision: 12-Sep-17 12 Document Number: 28120
For technical questions, contact: rfi@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
SUB-GROUP C1B PART OF
SAMPLE OF SUB-GROUP C1
4.9.2 Final measurements Visual examination No visible damage
Capacitance |C/C| 5 % of the value measured initially
Tangent of loss angle Increase of tan :
0.008 for: C 1 µF or
0.005 for: C > 1 µF
Compared to values measured initially
Insulation resistance As specified in section “Insulation resistance”
of this specification
SUB-GROUP C1
COMBINED SAMPLE OF
SPECIMENS OF SUB-GROUPS
C1A AND C1B
4.11 Climatic sequence
4.11.1 Initial measurements Capacitance
Measured in 4.4.2 and 4.9.2
Tangent of loss angle:
Measured initially in C1A and C1B
4.11.2 Dry heat Temperature: 110 °C
4.11.3 Damp heat cyclic
Test Db
First cycle
Duration: 16 h
4.11.4 Cold Temperature: - 55 °C
4.11.5 Damp heat cyclic
Test Db
remaining cycles
Duration: 2 h
4.11.6 Final measurements Visual examination No visible damage
Legible marking
Capacitance |C/C| 5 % of the value measured in 4.11.1.
Tangent of loss angle Increase of tan :
0.008 for: C 1 µF or
0.005 for: C > 1 µF
Compared to values measured in 4.11.1.
Voltage proof
1350 VDC; 1 min between terminations
No permanent breakdown or flash-over
Insulation resistance 50 % of values specified in section “Insulation
resistance” of this specification
SUB GROUP C2
4.12 Damp heat steady state 56 days, 40 °C, 90 % to 95 % RH
No load
4.12.1 Initial measurements Capacitance
Tangent of loss angle at 1 kHz
GROUP C INSPECTION REQUIREMENTS
SUB-CLAUSE NUMBER AND TEST CONDITIONS PERFORMANCE REQUIREMENTS
MKP336 2 X2
www.vishay.com Vishay BCcomponents
Not Recommended for New Designs, Use MKP339 X2
Revision: 12-Sep-17 13 Document Number: 28120
For technical questions, contact: rfi@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
SUB GROUP C2
4.12.3 Final measurements Visual examination No visible damage
Legible marking
Capacitance |C/C| 5 % of the value measured in 4.12.1.
Tangent of loss angle Increase of tan :
0.008 for: C 1 µF or
0.005 for: C > 1 µF
Compared to values measured in 4.12.1.
Voltage proof
1350 VDC; 1 min between terminations
No permanent breakdown or flash-over
Insulation resistance 50 % of values specified in section “Insulation
resistance” of this specification
SUB-GROUP C3
4.13.1 Initial measurements Capacitance
Tangent of loss angle:
For C 1 µF at 10 kHz
For C > 1 µF at 1 kHz
4.13 Impulse voltage 3 successive impulses, full wave, peak voltage:
2.5 kV for C 1 µF
2.5 kV/C for C > 1 µF
Max. 24 pulses
No selfhealing breakdowns or flashover
4.14 Endurance Duration: 1000 h
1.25 x URAC at 110 °C
Once in every hour the voltage is increased to
1000 VRMS for 0.1 s via resistor of 47 ± 5 %
4.14.7 Final measurements Visual examination No visible damage
Legible marking
Capacitance |C/C| 10 % compared to values measured in
4.13.1.
Tangent of loss angle Increase of tan :
0.008 for: C 1 µF or
0.005 for: C > 1 µF
Compared to values measured in 4.13.1.
Voltage proof
1350 VDC; 1 min between terminations
2120 VAC; 1 min between terminations
and case
No permanent breakdown or flash-over
Insulation resistance 50 % of values specified in section “Insulation
resistance” of this specification
SUB-GROUP C4
4.15 Charge and discharge 10 000 cycles
Charged to 435 VDC
Discharge resistance:
GROUP C INSPECTION REQUIREMENTS
SUB-CLAUSE NUMBER AND TEST CONDITIONS PERFORMANCE REQUIREMENTS
R435 VDC
1.25 x C dU/dt
------------------------------------------------
=
MKP336 2 X2
www.vishay.com Vishay BCcomponents
Not Recommended for New Designs, Use MKP339 X2
Revision: 12-Sep-17 14 Document Number: 28120
For technical questions, contact: rfi@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
SUB-GROUP C4
4.15.1 Initial measurements Capacitance
Tangent of loss angle:
For C 1 µF at 10 kHz
For C > 1 µF at 1 kHz
4.15.3 Final measurements Capacitance |C/C| 10 % compared to values measured in
4.15.1.
Tangent of loss angle Increase of tan :
0.008 for: C 1 µF or
0.005 for: C > 1 µF
Compared to values measured in 4.15.1.
Insulation resistance 50 % of values specified in section “Insulation
resistance” of this specification
SUB-GROUP C5
4.16 Radio frequency
characteristic
Resonance frequency 0.9 times the value as specified in section
“Resonant frequency” of this specification
SUB-GROUP C6
4.17 Passive flammability
Class B
Bore of gas jet: Ø 0.5 mm
Fuel: Butane
Test duration for actual volume V in mm:
V 250: 10 s
250 < V 500: 20 s
500 < V 1750: 30 s
V > 1750: 60 s
One flame application
After removing test flame from capacitor, the
capacitor must not continue to burn for more
than 10 s. No burning particle must drop from
the sample.
SUB-GROUP C7
4.18 Active flammability 20 cycles of 2.5 kV discharges on the test
capacitor connected to URAC.
The cheese cloth around the capacitors shall
not burn with a flame.
No electrical measurements are required.
GROUP C INSPECTION REQUIREMENTS
SUB-CLAUSE NUMBER AND TEST CONDITIONS PERFORMANCE REQUIREMENTS
45.0°
~ 8 mm
12 mm
Legal Disclaimer Notice
www.vishay.com Vishay
Revision: 08-Feb-17 1Document Number: 91000
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of
typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding
statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a
particular product with the properties described in the product specification is suitable for use in a particular application.
Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over
time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk.
Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for
such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document
or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
© 2017 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED
