199 RadHard MSI Logic
UT54ACS280/UT54ACTS280
Radiation-Hardened
9-Bit Parity Generators/Checkers
FEATURES
Generates either odd or even parity for nine data lines
Cascadable for n-bits parity
radiation-hardened CMOS
- Latchup immune
High speed
Low power consumption
Single 5 volt supply
Available QML Q or V processes
Flexible package
- 14-pin DIP
- 14-lead flatpack
DESCRIPTION
The UT54ACS280 and the UT54ACTS280 are 9-bit parity gen-
erators/checkers that use high-performance circuitry and fea-
tures odd and even outputs to facilitate operation of either odd
or even parity application. The word-length capability is easily
expanded by cascading.
The devices are characterized over full military temperature
range of -55 C to +125 C.
FUNCTION TABLE
LOGIC SYMBOL
PINOUTS 14-Pin DIP
Top View
14-Lead Flatpack
Top View
NUMBER OF INPUTS A THRU I
THAT ARE HIGH OUTPUT
EVEN ODD
0,2,4,6,8 HL
1,3,5,7,9 LH
(5) EVEN
(6)
(8)
A
Note:
1. Logic symbol in accordance with ANSI/IEEE standard 91-1984 and IEC
Publication 617-12.
2k
(9)
B(10)
C(11)
D(12)
E(13)
F(1)
G(2)
H(4)
ODD
I
1
2
3
4
5
7
6
14
13
12
11
10
8
9
G
H
NC
I
EVEN
ODD
VSS
VDD
F
E
D
C
B
A
1
2
3
4
5
7
6
14
13
12
11
10
8
9
VDD
F
E
D
C
B
A
G
H
NC
I
EVEN
ODD
VSS
RadHard MSI Logic 200
UT54ACS280/UT54ACTS280
LOGIC DIAGRAM
A
B
C
D
E
G
H
I
F
(8)
(9)(
(10)
(11)
(12)
(13)
(1)
(2)
(4)
(5)
(6)
EVEN
ODD
201 RadHard MSI Logic
UT54ACS280/UT54ACTS280
RADIATION HARDNESS SPECIFICATIONS 1
Notes:
1. Logic will not latchup during radiation exposure within the limits defined in the table.
2. Device storage elements are immune to SEU affects.
ABSOLUTE MAXIMUM RATINGS
Note:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, functional operation of the device
at these or any other conditions beyond limits indicated in the operational sections is not recommended. Exposure to absolute maximum rating conditions for
extended periods may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
PARAMETER LIMIT UNITS
Total Dose 1.0E6 rads(Si)
SEU Threshold 280 MeV-cm2/mg
SEL Threshold 120 MeV-cm2/mg
Neutron Fluence 1.0E14 n/cm2
SYMBOL PARAMETER LIMIT UNITS
VDD Supply voltage -0.3 to 7.0 V
VI/O Input voltage any pin -.3 to VDD +.3 V
TSTG Storage Temperature range -65 to +150 C
TJMaximum junction temperature +175 C
TLS Lead temperature (soldering 5 seconds) +300 C
JC Thermal resistance junction to case 20 C/W
IIDC input current 10 mA
PDMaximum power dissipation 1W
SYMBOL PARAMETER LIMIT UNITS
VDD Supply voltage 4.5 to 5.5 V
VIN Input voltage any pin 0 to VDD V
TCTemperature range -55 to + 125 C
RadHard MSI Logic 202
UT54ACS280/UT54ACTS280
DC ELECTRICAL CHARACTERISTICS 7
(VDD = 5.0V 10%; VSS = 0V 6, -55 C < TC < +125 C)
SYMBOL PARAMETER CONDITION MIN MAX UNIT
VIL Low-level input voltage 1
ACTS
ACS
0.8
.3VDD
V
VIH High-level input voltage 1
ACTS
ACS
.5VDD
.7VDD
V
IIN Input leakage current
ACTS/ACS VIN = VDD or VSS -1 1A
VOL Low-level output voltage 3
ACTS
ACS IOL = 8.0mA
IOL = 100 A0.40
0.25 V
VOH High-level output voltage 3
ACTS
ACS IOH = -8.0mA
IOH = -100 A.7VDD
VDD - 0.25 V
IOS Short-circuit output current 2 ,4
ACTS/ACS VO = VDD and VSS -200 200 mA
IOL Output current10
(Sink)
VIN = VDD or VSS
VOL = 0.4V
8mA
IOH Output current10
(Source)
VIN = VDD or VSS
VOH = VDD - 0.4V
-8 mA
Ptotal Power dissipation 2, 8, 9 CL = 50pF 2.2 mW/
MHz
IDDQ Quiescent Supply Current VDD = 5.5V 10 A
IDDQ Quiescent Supply Current Delta
ACTS For input under test
VIN = VDD - 2.1V
For all other inputs
VIN = VDD or VSS
VDD = 5.5V
1.6 mA
CIN Input capacitance 5 = 1MHz @ 0V 15 pF
COUT Output capacitance 5 = 1MHz @ 0V 15 pF
203 RadHard MSI Logic
UT54ACS280/UT54ACTS280
Notes:
1. Functional tests are conducted in accordance with MIL-STD-883 with the following input test conditions: VIH = VIH(min) + 20%, - 0%; VIL = VIL(max) + 0%,
- 50%, as specified herein, for TTL, CMOS, or Schmitt compatible inputs. Devices may be tested using any input voltage within the above specified range, but
are guaranteed to VIH(min) and VIL(max).
2. Supplied as a design limit but not guaranteed or tested.
3. Per MIL-PRF-38535, for current density 5.0E5 amps/cm2, the maximum product of load capacitance (per output buffer) times frequency should not exceed
3,765 pF/MHz.
4. Not more than one output may be shorted at a time for maximum duration of one second.
5. Capacitance measured for initial qualification and when design changes may affect the value. Capacitance is measured between the designated terminal and VSS
at frequency of 1MHz and a signal amplitude of 50mV rms maximum.
6. Maximum allowable relative shift equals 50mV.
7. All specifications valid for radiation dose 1E6 rads(Si).
8. Power does not include power contribution of any TTL output sink current.
9. Power dissipation specified per switching output.
10. This value is guaranteed based on characterization data, but not tested.
RadHard MSI Logic 204
UT54ACS280/UT54ACTS280
AC ELECTRICAL CHARACTERISTICS 2
(VDD = 5.0V 10%; VSS = 0V 1, -55 C < TC < +125 C)
Notes:
1. Maximum allowable relative shift equals 50mV.
2. All specifications valid for radiation dose 1E6 rads(Si).
SYMBOL PARAMETER MINIMUM MAXIMUM UNIT
tPLH Any input to even 1 20 ns
tPHL Any input to even 1 20 ns
tPHL Any input to odd 1 22 ns
tPLH Any input to odd 1 20 ns
