NOT RECOMMENDED FOR NEW DESIGNS USE ES1A-LTP~ES1J-LTP SERIES MCC R ES1A THRU ES1M Micro Commercial Components Micro Commercial Components 130 W Cochran St, Unit B Simi Valley, CA 93065 Tel:818-701-4933 Features * * * * x x Halogen free available upon request by adding suffix "-HF" Lead Free Finish/Rohs Compliant (Note1) ("P"Suffix designates Compliant. See ordering information) Epoxy meets UL 94 V-0 flammability rating Moisture Sensitivity Level 1 High Temp Soldering: 260qC for 10 Seconds At Terminals Superfast Recovery Times For High Efficiency 1 Amp Ultra Fast Recovery Silicon Rectifier 50 to 1000 Volts Maximum Ratings Operating Temperature: -50qC to +150qC Storage Temperature: -50qC to +150qC Maximum Thermal Resistance; 15qC/W Junction To Lead x x x MCC Part Number Device Marking ES1A ES1B ES1C ES1D ES1G ES1J ES1K ES1M ES1A ES1B ES1C ES1D ES1G ES1J ES1K ES1M Maximum Recurrent Peak Reverse Voltage 50V 100V 150V 200V 400V 600V 800V 1000V Maximum RMS Voltage 35V 70V 105V 140V 280V 420V 560V 700V DO-214AC (HSMA) (High Profile) Maximum DC Blocking Voltage 50V 100V 150V 200V 400V 600V 800V 1000V H Cathode Band J A E Note: D B F Electrical Characteristics @ 25qC Unless Otherwise Specified Average Forward IF(AV) 1.0A Ta = 75qC Current Peak Forward Surge IFSM 30A 8.3ms, half sine Current Maximum Instantaneous Forward Voltage VF ES1A-D .975V IFM = 1.0A; ES1G-J 1.35V TJ = 25qC* ES1K~M 1.70V Maximum DC IR Reverse Current At 5PA TJ = 25qC Rated DC Blocking 100PA TJ = 100qC Voltage Maximum Reverse Recovery Time Trr IF=0.5A, IR=1.0A, ES1A-D 50ns ES1G-K 75ns Irr=0.25A ES1M 100ns Typical Junction CJ 45pF Measured at Capacitance 1.0MHz, VR=4.0V *Pulse test: Pulse width 200 Psec, Duty cycle 2% C G DIMENSIONS DIM A B C D E F G H J INCHES MIN .078 .067 .002 --.035 .065 .205 .160 .100 MM MIN 1.98 1.70 .05 --.89 1.65 5.21 4.06 2.57 MAX .116 .089 .008 .02 .055 .096 .224 .180 .112 MAX 2.95 2.25 .20 .51 1.40 2.45 5.69 4.57 2.84 NOTE SUGGESTED SOLDER PAD LAYOUT 0.090" 0.085" 0.070" 1. High Temperature Solder Exemptions Applied, see EU Directive Annex 7. Revision: C www.mccsemi.com 1 of 4 2013/01/01 MCC ES1A thru ES1M Micro Commercial Components Figure 1 Typical Forward Characteristics Figure 2 Forward Derating Curve 2.4 INSTANTANEOUS FORWARD CURRENT,(A) 50 2.2 2.0 ES1A~ES1D 10 ES1G~ES1J 1.8 1.6 3.0 1.4 ES1K~ES1M 1.0 Amps 1.2 1.0 .8 .6 0.1 .4 Single Phase, Half Wave .2 60Hz Resistive or Inductive Load 0 .01 .6 .8 1.0 1.2 1.4 1.6 1.8 2.0 0 25 50 75 100 125 150 C Average Forward Rectified Current - Amperesversus Ambient Temperature -C FORWARD VOLTAGE,(V) Instantaneous Forward Current - Amperesversus Instantaneous Forward Voltage - Volts Figure 3 Junction Capacitance 100 60 40 20 pF TJ=25C;f=1MHZ 10 6 4 2 1 .1 .2 .4 1 Volts 2 4 10 20 40 100 200 400 1000 Junction Capacitance - pFversus Reverse Voltage - Volts Revision: C www.mccsemi.com 2 of 4 2013/01/01 R MCC ES1A thru ES1M R Micro Commercial Components Figure 5 Typical Reverse Characteristics Figure 4 Peak Forward Surge Current 100 30 25 Tj = 100C 20 10 15 Amps 10 5 0 1.0 1 2 4 6 8 10 20 40 Tj = 25C 60 80 100 Cycles Peak Forward Surge Current - Amperesversus Number Of Cycles At 60Hz - Cycles 0.1 0 40 80 120 PERCENT OF RATED PEAK REVERSE VOLTAGE (%) Figure 6 Reverse Recovery Time Characteristic And Test Circuit Diagram 50 10 trr +0.5A 0 -0.25 Pulse Generator Note 2 25Vdc -1.0 1 Oscilloscope Note 1 1cm Set Time Base for 20/100ns/cm Notes: 1. Rise Time = 7ns max. Input impedance = 1 megohm, 22pF 2. Rise Time = 10ns max. Source impedance = 50 ohms 3. Resistors are non-inductive Figure 7 New SMA Assembly Round Lead Process www.mccsemi.com Revision: C 3 of 4 2013/01/01 MCC R Micro Commercial Components Ordering Information : Device Packing Part Number-TP Tape&Reel: 3Kpcs/Reel Note : Adding "-HF" suffix for halogen free, eg. Part Number-TP-HF ***IMPORTANT NOTICE*** Micro Commercial Components Corp. reserves the right to make changes without further notice to any product herein to make corrections, modifications , enhancements , improvements , or other changes . Micro Commercial Components Corp . does not assume any liability arising out of the application or use of any product described herein; neither does it convey any license under its patent rights ,nor the rights of others . The user of products in such applications shall assume all risks of such use and will agree to hold Micro Commercial Components Corp . and all the companies whose products are represented on our website, harmless against all damages. ***LIFE SUPPORT*** MCC's products are not authorized for use as critical components in life support devices or systems without the express written approval of Micro Commercial Components Corporation. ***CUSTOMER AWARENESS*** Counterfeiting of semiconductor parts is a growing problem in the industry. Micro Commercial Components (MCC) is taking strong measures to protect ourselves and our customers from the proliferation of counterfeit parts. MCC strongly encourages customers to purchase MCC parts either directly from MCC or from Authorized MCC Distributors who are listed by country on our web page cited below. Products customers buy either from MCC directly or from Authorized MCC Distributors are genuine parts, have full traceability, meet MCC's quality standards for handling and storage. MCC will not provide any warranty coverage or other assistance for parts bought from Unauthorized Sources. MCC is committed to combat this global problem and encourage our customers to do their part in stopping this practice by buying direct or from authorized distributors. www.mccsemi.com Revision: C 4 of 4 2013/01/01 1