
Connector
Accessories
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
Printed in U.S.A.
www.glenair.com
CAGE CODE 06324
© 2008 Glenair, Inc.
E-Mail: sales@glenair.com
G-25
G
TABLE III: BACKSHELL DIMENSIONS
Shell Size
F H E Max. F Max. G Max. H Max. J Ref. Max. Dash
No. (F, H)
08 09 0.75 (1.9) 1.5 (3.8) 0.639 (1.6) 1.38 (3.5) 0.45 (1.1) 01
10 11 0.81 (2.1) 1.55 (3.9) 0.664 (1.7) 1.41 (3.6) 0.58 (1.5) 02
12 13 0.87 (2.2) 1.61 (4.1) 0.688 (1.7) 1.43 (3.6) 0.69 (1.8) 04
14 15 0.92 (2.3) 1.68 (4.3) 0.705 (1.8) 1.46 (3.7) 0.82 (2.1) 05
16 17 0.98 (2.5) 1.74 (4.4) 0.732 (1.9) 1.48 (3.8) 0.94 (2.4) 06
18 19 1.02 (2.6) 1.76 (4.5) 0.748 (1.9) 1.49 (3.8) 1.03 (2.6) 06
20 21 1.08 (2.7) 1.82 (4.6) 0.773 (2.0) 1.51 (3.8) 1.16 (2.9) 07
22 23 1.14 (2.9) 1.90 (4.8) 0.800 (2.0) 1.55 (3.9) 1.28 (3.3) 08
24 25 1.20 (3.0) 1.97 (5.0) 0.823 (2.1) 1.58 (4.0) 1.41 (3.6) 09
TABLE IV: CABLE ENTRY
Dash No. K Max. L Max. Cable Entry
Min. Max.
1 0.843 (2.1) 0.78 (2.0) 0.125 (0.3) 0.250 (0.6)
2 0.968 (2.5) 0.97 (2.5) 0.156 (0.4) 0.375 (1.0)
3 1.046 (2.7) 1.05 (2.7) 0.250 (0.6) 0.438 (1.1)
4 1.156 (2.9) 1.15 (2.9) 0.280 (0.7) 0.500 (1.3)
5 1.218 (3.1) 1.22 (3.1) 0.375 (1.0) 0.625 (1.6)
6 1.343 (3.4) 1.34 (3.4) 0.500 (1.3) 0.750 (1.9)
7 1.468 (3.7) 1.47 (3.7) 0.625 (1.6) 0.875 (2.2)
8 1.593 (4.0) 1.59 (4.0) 0.750 (1.9) 1.000 (2.5)
9 1.718 (4.4) 1.72 (4.4) 0.875 (2.2) 1.125 (2.9)
10 1.843 (4.7) 1.84 (4.7) 1.000 (2.5) 1.250 (3.2)
447-425
EMI/RFI Non-Environmental Band-in-a-Can Backshell
With Cable Clamp Strain-Relief
Rotatable Coupling - Standard Prole
APPLICATION NOTES
Standard minimum length for Style I is 1 inch (25.4), Style II 1. is 1.5 inches (38.1). Consult factory about shorter lengths
(Note: Applies to Symbol S Straight only).
When cable diameter exceeds “Max Dash No” in Table I, Style 2. II will be supplied.
For effective grounding, connector with conductive nish 3. should be used.
Glenair Series 600 Backshell Assembly tools are 4. recommended for assemply and installation.
For shield termination see Glenair Drawings 600-050 and 5. 600-052.
Material/Finish: 6. Adapters, Elbows, Coupling Nuts, Ferrule, Clamp - Al
Alloy/See Table I
Hardware - Cres/Passivate
Metric dimensions (mm) are indicated in parentheses. 7.
TABLE II: FINISHES
Symbol Finish
BCadmium Plate, Olive Drab
CAnodize, Black
GB Black Anodize, Hard Coat
MElectroless Nickel
NCad Plate, Olive Drab over
Electroless Nickel
NF Cadmium Plate, Olive Drab over
Electroless Nickel
MT Ni-PTFE 1000 Hour GreyTM
Nickel Fluorocarbon Polymer
Z1 Stainless Steel Passivate
ZL CRES, Electroless Nickel
ZN Zinc-Nickel