1
This document is subject to change without notice.
Date Published: July 2016
CDS-0021-02 (Issue A)
DESCRIPTION
Low Noise and High Gain
Original Dual Mold Plastic package
FEATURES
Low noise figure and high associated gain
NF=0.42dB TYP., Ga=12.2dB TYP. @VDS=2V,
ID=10mA, f=12GHz
ORDERING INFORMATION
PACKAGE
Flat-lead 4-pin thin-type super minimold
package
APPLICATIONS
DBS LNB gain-stage, Mix-stage
Low noise amplifier for microwave
communication systems
Part Number
Order Number
Package
Marking
Description
CE3514M4
CE3514M4-C2
Flat-lead 4-pin
thin-type super
minimold
package
C0F
• Embossed tape 8 mm wide
• Pin 1(Source), Pin 2 (Drain)
Face the perforation side of
the Tape
• MOQ 15 kpcs/reel
12GHz Low Noise FET in Dual Mold Plastic PKG
CE3514M4
This document is subject to change without notice.
2
PIN CONFIGURATION :
ABSOLUTE MAXIMUM RATINGS
(TA = +25˚C, unless otherwise specified)
Parameter
Symbol
Rating
Unit
Drain to Source Voltage
VDS
4.0
V
Gate to Source Voltage
VGS
-3.0
V
Drain Current
ID
IDSS
mA
Gate Current
IG
80
µA
Total Power Dissipation
Ptot
125
mW
Channel Temperature
Tch
+150
°C
Storage Temperature
Tstg
-55 to +125
°C
Operation Temperature
Top
-55 to +125Note
°C
Note Refer to Total Power Dissipation vs. Ambient Temperature graph on page 4
RECOMMENDED OPERATING RANGE
(TA = +25˚C, unless otherwise specified)
Parameter
Symbol
MIN.
TYP.
MAX.
Unit
Drain to Source Voltage
VDS
+1
+2
+3
V
Drain Current
ID
5
10
15
mA
PIN No.
PIN Name
1
2
3
4
Source
Drain
Source
Gate
CE3514M4
This document is subject to change without notice.
3
ELECTRICAL CHARACTERISTICS
(TA = +25˚C, unless otherwise specified)
Parameter
Symbol
Condition
MIN.
TYP.
MAX.
Unit
Gate to Source Leak Current
IGSO
VGS = -3.0V
-
0.4
10
µA
Saturated Drain Current
IDSS
VDS = 2V, VGS = 0V
27
47.5
68
mA
Gate to Source Cut-off Voltage
VGS(off)
VDS = 2V, ID = 120µA
-1.10
-0.75
-0.39
V
Transconductance
Gm
VDS = 2V, ID = 10mA
54
69
-
mS
Noise Figure
NF
VDS = 2V, ID = 10mA,
f = 12GHz
-
0.42
0.62
dB
Associated Gain
Ga
10.5
12.2
-
dB
CE3514M4
This document is subject to change without notice.
4
TYPICAL CHARACTERISTICS :
(TA=+25℃, unless otherwise specified)
TOTAL POWER DISSIPATION
VS. AMBIENT TEMPERATURE
DRAIN CURRENT VS.
DRAIN TO SOURCE VOLTAGE
DRAIN CURRENT VS.
GATE TO SOURCE VOLTAGE
MINIMUM NOISE FIGURE &
ASSOCIATED GAIN VS. DRAIN CURRENT
CE3514M4
This document is subject to change without notice.
5
S-PARAMETERS
S-Parameters are available on the CEL web site.
RECOMMENDED SOLDERING CONDITIONS
Recommended Soldering Conditions are provided on the CEL web site.
PACKAGE DIMENSIONS
CE3514M4
This document is subject to change without notice.
6
REVISION HISTORY
Version
Change to current version
Page(s)
CDS-0021-02 (Issue A)
July 28, 2016
Initial datasheet
N/A
CE3514M4
This document is subject to change without notice.
7
[CAUTION]
・ All information included in this document is current as of the date this document is issued. Such information,
however, is subject to change without any prior notice.
・ You should not alter, modify, copy, or otherwise misappropriate any CEL product, whether in whole or in part.
・ CEL does not assume any liability for infringement of patents, copyrights, or other intellectual property rights of
third parties by or arising from the use of CEL products or technical information described in this document. No
license, expressed, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual
property rights of CEL or others.
・ Descriptions of circuits, software and other related information in this document are provided only to illustrate the
operation of semiconductor products and application examples. You are fully responsible for the incorporation of
these circuits, software, and information in the design of your equipment. CEL assumes no responsibility for any
losses incurred by you or third parties arising from the use of these circuits, software, or information.
・ CEL has used reasonable care in preparing the information included in this document, but CEL does not warrant
that such information is error free. CEL assumes no liability whatsoever for any damages incurred by you resulting
from errors in or omissions from the information included herein.
・ Although CEL endeavors to improve the quality and reliability of its products, semiconductor products have specific
characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions.
Please be sure to implement safety measures to guard them against the possibility of physical injury, and injury or
damage caused by fire in the event of the failure of a CEL product, such as safety design for hardware and software
including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging
degradation or any other appropriate measures
Because the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final
products or system manufactured by you.
・ Please use CEL products in compliance with all applicable laws and regulations that regulate the inclusion or use of
controlled substances, including without limitation, the EU RoHS Directive.
CEL assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and
regulations.
・ This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written consent
of CEL.
・ Please contact CEL if you have any questions regarding the information contained in this document or CEL
products, or if you have any other inquiries.
CE3514M4
This document is subject to change without notice.
8
[CAUTION]
This product uses gallium arsenide (GaAs) of the toxic substance appointed in laws and ordinances.
GaAs vapor and powder are hazardous to human health if inhaled or ingested.
・ Do not dispose in fire or break up this product.
・ Do not chemically make gas or powder with this product.
・ When discarding this product, please obey the laws of your country.
・ Do not lick the product or in any way allow it to enter the mouth.
[CAUTION]
Although this device is designed to be as robust as possible, ESD (Electrostatic Discharge) can
damage this device. This device must be protected at all times from ESD. Static charges may easily
produce potentials of several kilovolts on the human body or equipment, which can discharge
without detection. Industry-standard ESD precautions should be used at all times.
CEL Headquarters • 4590 Patrick Henry Drive • Santa Clara, CA 95054 • Tel: (408) 919-2500 • www.cel.com
For a complete list of sales offices, representatives and distributors,
Please visit our website: www.cel.com/contactus
For inquiries email us at rfw@cel.com