V-166-1A5(R) - Omron Electronics

Snap Action Switch V121

Snap Action Switch

General Purpose Snap Action Switch

• Industry standard design with switching currents of 10A to 21A

• Widely used for applications where long life expectancy and

high reliability is required.

• Choose from a variety of levers, terminals and operating forces.

• Right and Left Barrier options are available for the V-21 and

V-16 models

• Heat resistant versions of the V-15 and V-10 are available.

• RoHS Compliant

Ordering Information

■Model Number Legend

V - - - -

1. Ratings

21: 21 A at 250 VAC

16: 16 A at 250 VAC

2. Contact Gap

None: 1 mm (F gap)

G: 0.5 mm (G gap)

15: 15 A at 250 VAC

11: 11 A at 250 VAC

10: 10 A at 250 VAC

4: 100 gf

7. Maximum Operating Force

6: 400 gf

5: 200 gf

8. Special Purpose

T: Heat resistive

(V-15 and V-10, only)

4. Contact Form

1: SPDT

COM Terminal, Bottom position:

COM Terminal, Side position:

2: SPST-NC

9. Mounting Hole Size

None: 3.1 mm

None: Standard

K: 2.9 mm

3: SPST-NO

4: SPDT

5: SPST-NC

6: SPST-NO

6. Insulation Barrier

None: Without Barrier

R: Right-hand barrier

L: Left-hand barrier

Note: These OF values are for

the pin plunger models.

3. Actuator

None: Pin plunger

1: Short hinge lever

2: Hinge lever

3: Long hinge lever

4: Simulated roller lever

5: Short hinge roller lever

6: Hinge roller lever

5. Terminals

A: Solder terminals

C2: Quick-connect terminal (#187)

C: Quick-connect terminal (#250)

3 4 521 7 8 96

(Barriers available for V-21 and V-16, only)

Note: Consult Omron regarding nomenclature combinations and part numbers

not found in this datasheet.

122 Snap Action Switch V

■Available Combinations

Note: 1. ❍: Available model.

Consult OMRON for specific models with standard approval.

■List of Models

Thermoplastic Case

21 A (OF: 400 gf)

Note: 1. Add “G” to the part number in the appropriate location to obtain a 0.5 mm contact gap. Add “-K” to the part number in the appropriate

location to obtain 2.9 mm mounting holes. Example: V-21G2-1C6-K

2. Not all combinations are available. Consult Omron regarding nomenclature combinations and part numbers not found in this datasheet.

Thermoplastic case Thermosetting case

ModelV-21V-16V-11V-15 V-10

Rated Current 21 A 16 A 11 A 15 A 10 A

COM

terminal

position

Insulation

Barrier Heat

Resistance

Terminal Symbol

400 gf 400 gf 200 gf 100 gf 400 gf 200 gf 200 gf 100 gf

Bottom No Standard

(80°C)

Solder terminals (A) - - - ❍❍❍❍❍❍❍

Quick-connect

terminals (#187)(C2) - - - ❍❍❍❍❍❍❍

Quick-connect

terminals (#250)(C) ❍❍❍❍❍❍❍❍

Heat

resistant

(150°C)

Solder terminals (A) - - - - - - - - - - - - ❍❍❍❍

Quick-connect

terminals (#187)(C2) - - - - - - - - - - - - ❍❍❍❍

Quick-connect

terminals (#250)(C) - - -- - -- - -- - -- - -- - -- - -- - -

Yes Standard

(80°C)

Solder terminals (A) - - - ❍❍- - - - - - - - - - - - - - -

Quick-connect

terminals (#187)(C2) - - - ❍❍- - - - - - - - - - - - - - -

Quick-connect

terminals (#250)(C) ❍❍❍- - - - - - - - - - - - - - -

Side No Standard

(80°C)

Solder terminals (A) - - - - - - - - - - - - ❍❍❍❍

Quick-connect

terminals (#187)(C2) - - - - - - - - - - - - ❍❍❍❍

Quick-connect

terminals (#250)(C) ❍- - - - - - - - - - - - - - - - - - - - -

Common

terminal

position Contact

form Terminal style Actuator

Bottom SPDT Quick-connect

(#250) (C)

V-21-1C6 V-21-1CR6 V-21-1CL6

SPST-NCV-21-2C6 V-21-2CR6 V-21-2CL6

SPST-NOV-21-3C6 V-21-3CR6 V-21-3CL6

SPDT V-211-1C6 V-211-1CR6 V-211-1CL6

V-212-1C6 V-212-1CR6 V-212-1C6

V-213-1C6 V-213-1CR6 V-213-1CL6

V-214-1C6 V-214-1CR6 V-214-1CL6

V-215-1C6 V-215-1CR6 V-215-1CL6

V-216-1C6 V-216-1CR6 V-216-1CL6

Without barrier

Right-hand barrier

Left-hand barrier

Pin plunger

Short hinge lever

Hinge lever

Long hinge lever

Simulated roller lever

Short hinge roller lever

Hinge roller lever

Snap Action Switch V123

16 A (OF: 200 gf)

11 A (OF: 100 gf)

Note: 1. Add “G” to the part number in the appropriate location to obtain a 0.5 mm contact gap. Add “-K” to the part number in the appropriate

location to obtain 2.9 mm mounting holes. Examples: 1) V-16G3-1C25-K 2) V-11G-1A4-K

2. Not all combinations are available. Consult Omron regarding nomenclature combinations and part numbers not found in this datasheet.

Common

terminal

position Contact

form Terminal style Actuator

Bottom SPDT A V-16-1A5 V-16-1AR5 V-16-1AL5

C2 V-16-1C25 V-16-1C2R5 V-16-1C2L5

CV-16-1C5 - - - - - -

SPST-NCA V-16-2A5 V-16-2AR5 V-16-2AL5

C2 V-16-2C25 V-16-2C2R5 V-16-2C2L5

CV-16-2C5 - - - - - -

SPST-NOA V-16-3A5 V-16-3AR5 V-16-3AL5

C2 V-16-3C25 V-16-3C2R5 V-16-3C2L5

CV-16-3C5 - - - - - -

SPDT A V-161-1A5 V-161-1AR5 V-161-1AL5

C2 V-161-1C25 V-161-1C2R5 V-161-1C2L5

CV-161-1C5 - - - - - -

AV-162-1A5 V-162-1AR5 V-162-1AL5

C2 V-162-1C25 V-162-1C2R5 V-162-1C2L5

CV-162-1C5 - - - - - -

AV-163-1A5 V-163-1AR5 V-163-1AL5

C2 V-163-1C25 V-163-1C2R5 V-163-1C2L5

CV-163-1C5 - - - - - -

AV-164-1A5 V-164-1AR5 V-164-1AL5

C2 V-164-1C25 V-164-1C2R5 V-164-1C2L5

CV-164-1C5 - - - - - -

AV-165-1A5 V-165-1AR5 V-165-1AL5

C2 V-165-1C25 V-165-1C2R5 V-165-1C2L5

CV-165-1C5 - - - - - -

AV-166-1A5 V-166-1AR5 V-166-1AL5

C2 V-166-1C25 V-166-1C2R5 V-166-1C2L5

CV-166-1C5 - - - - - -

Without barrier

Right-hand barrier

Left-hand barrier

Pin plunger

Short hinge lever

Hinge lever

Long hinge lever

Simulated roller lever

Short hinge roller lever

Hinge roller lever

Common

terminal

position Contact form Terminal style Actuator

Bottom SPDT A V-11-1A4

C2 V-11-1C24

CV-11-1C4

AV-111-1A4

C2 V-111-1C24

CV-111-1C4

AV-112-1A4

C2 V-112-1C24

CV-112-1C4

AV-113-1A4

C2 V-113-1C24

CV-113-1C4

AV-114-1A4

C2 V-114-1C24

CV-114-1C4

AV-115-1A4

C2 V-115-1C24

CV-115-1C4

AV-116-1A4

C2 V-116-1C24

CV-116-1C4

Without barrier

Pin plunger

Short hinge lever

Hinge lever

Long hinge lever

Simulated roller lever

Short hinge roller lever

Hinge roller lever

124 Snap Action Switch V

Thermosetting Case

Standard models - 15 A / 10 A

Note: 1. For SPST-NC and SPST-NO with levers consult Omron.

2. Not all combinations are available. Consult Omron regarding nomenclature combinations and part numbers not found in this datasheet.

Heat Resistant Models (Up to 150°C) - 15 A / 10A

Note: 1. Add “G” to the part number in the appropriate location to obtain a 0.5 mm contact gap. Add “-K” to the part number in the appropriate

location to obtain 2.9 mm mounting holes. Add “C2” to the part number in the appropriate location to obtain versions with #187 quick-

connect terminals. Example: 1) V-15G1-1C25-T-K

2. Not all combinations are available. Consult Omron regarding nomenclature combinations and part numbers not found in this datasheet.

Common

terminal

position

Contact

form Terminal style Actuator 15 A 10 A

200 gf 200 gf 100 gf

Bottom SPDT A V-15G-1A5-K V-10G-1A5-K V-10G-1A4-K

C2 V-15G-1C25-K V-10G-1C25-K V-10G-1C24-K

CV-15G-1C5-K — —

SPST-NCA V-15G-2A5-K V-10G-2A5-K V-10G-2A4-K

C2 V-15G-2C25-K V-10G-2C25-K V-10G-2C24-K

SPST-NOA V-15G-3A5-K V-10G-3A5-K V-10G-3A4-K

C2 V-15G-3C25-K V-10G-3C25-K V-10G-3C24-K

CV-15G-3C5-K — —

Side SPDT A V-15G-4A5-K V-10G-4A5-K V-10G-4A4-K

SPST-NCV-15G-5A5-K V-10G-5A5-K V-10G-5A4-K

SPST-NOV-15G-6A5-K V-10G-6A5-K V-10G-6A4-K

Bottom SPDT A V-15G1-1A5-K V-10G1-1A5-K V-10G1-1A4-K

C2 V-15G1-1C25-K V-10G1-1C25-K V-10G1-1C24-K

AV-15G2-1A5-K V-10G2-1A5-K V-10G2-1A4-K

C2 V-15G2-1C25-K V-10G2-1C25-K V-10G2-1C24-K

AV-15G3-1A5-K V-10G3-1A5-K V-10G3-1A4-K

C2 V-15G3-1C25-K V-10G3-1C25-K V-10G3-1C24-K

AV-15G4-1A5-K V-10G4-1A5-K V-10G4-1A4-K

C2 V-15G4-1C25-K V-10G4-1C25-K V-10G4-1C24-K

AV-15G5-1A5-K V-10G5-1A5-K V-10G5-1A4-K

C2 V-15G5-1C25-K V-10G5-1C25-K V-10G5-1C24-K

AV-15G6-1A5-K V-10G6-1A5-K V-10G6-1A4-K

C2 V-15G6-1C25-K — V-10G6-1C24-K

Common

terminal

position

Contact

form Terminal style Actuator 15 A 10 A

200 gf 100 gf

Bottom SPDT Solder Terminals

(A)

V-15-1A5-T V-10-1A4-T

V-151-1A5-T V-101-1A4-T

V-152-1A5-T V-102-1A4-T

V-153-1A5-T V-103-1A4-T

V-154-1A5-T V-104-1A4-T

V-155-1A5-T V-105-1A4-T

V-156-1A5-T V-106-1A4-T

Pin plunger

Short hinge lever

Hinge lever

Long hinge lever

Simulated roller lever

Short hinge roller lever

Hinge roller lever

Pin plunger

Short hinge lever

Hinge lever

Long hinge lever

Simulated roller lever

Short hinge roller lever

Hinge roller lever

Snap Action Switch V125

Specifications

■Ratings (reference values)

Note: 1. The above current values are the normal current values of models with a contact gap of 1 mm (gap F), which vary with the normal current

values of models with a contact gap of 0.5 mm (gap G).

2. Inductive load has a power factor of 0.4 min. (AC) and a time constant of 7 ms max. (DC).

3. Lamp load has an inrush current of 10 times the steady-state current.

4. Motor load has an inrush current of 6 times the steady-state current.

The ratings values apply under the following test conditions: Ambient temperature: 20

C, Ambient humidity: 65

5%, Operating frequency: 30 operations/min

■Approved Standards

UL1054 (File No. E41515)

CSA C22.2 No.55 (File No. LR21642)

EN 61058-1 (File No. 129608, VDE approval)

Testing conditions: 5E4 (50,000 operations), T105 (0°C to 105°C)

EN 61058-1 (File No. T9451451, TÜV Rheinland approval)

Testing conditions: 5E4 (50,000 operations), T85 (0°C to 85°C)

Type Rated voltage Non-inductive load Inductive load

Resistive load Lamp load Inductive load Motor load

NC NO NC NO NC NO NC NO

V-21 250 VAC 21 A 3 A 12 A 4 A

8 VDC

30 VDC

125 VDC

250 VDC

21 A

14 A

0.6 A

0.3 A

5 A

0.1 A

0.05 A

12 A

0.6 A

0.3 A

7 A

5 A

0.1 A

0.05 A

V-16 250 VAC 16 A 2 A 10 A 3 A

8 VDC

30 VDC

125 VDC

250 VDC

16 A

10 A

0.6 A

0.3 A

4 A

0.1 A

0.05 A

10 A

0.6 A

0.3 A

6 A

4 A

0.1 A

0.05 A

V-15 250 VAC 15 A 2 A 10 A 3 A

8 VDC

30 VDC

125 VDC

250 VDC

15 A

10 A

0.6 A

0.3 A

4 A

0.1 A

0.05 A

10 A

0.6 A

0.3 A

6 A

4 A

0.1 A

0.05 A

V-11 250 VAC 11 A 1.5 A 6 A 2 A

8 VDC

30 VDC

125 VDC

250 VDC

11 A

6 A

0.6 A

0.3 A

3 A

0.1 A

0.05 A

6 A

0.6 A

0.3 A

3 A

0.1 A

0.05 A

V-10 250 VAC 10 A 1.5 A 6 A 2 A

8 VDC

30 VDC

125 VDC

250 VDC

10 A

6 A

0.6 A

0.3 A

3 A

0.1 A

0.05 A

6 A

0.6 A

0.3 A

3 A

0.1 A

0.05 A

Rated voltage V-21 V-16 V-15 V-11 V-10

125 VAC 21 A, 1/2 HP 16 A, 1/2 HP 15 A, 1/2 HP 11 A, 1/3 HP 10 A, 1/3 HP

250 VAC

125 VDC 0.6 A

250 VDC 0.3 A

Rated voltage V-21 V-16 V-11

250 VAC 20 (4) A 16 (4) A 11 (3) A

Rated voltage V-15 V-10

250 VAC 15 A 10 A

250 VDC 0.3 A

126 Snap Action Switch V

■Characteristics

Note: 1. Data shown are of initial value.

2. The dielectric strength shown is measured using a separator between the switch and metal mounting plate.

3. For pin plunger models, the above values apply for use at both the free position and total travel position. For lever models, they apply at

the total travel position.

4. For testing conditions, contact your OMRON sales representative.

■Contact Specifications

Note: Minimum applicable loads are indicated by N standard reference values. This value represents the failure rate at a 60% (λ60) reliability level

(JIS C5003). The equation λ60=0.5 x 10-6 / operations indicates that a failure rate of 1/2,000,000 operations can be expected at a reliability

level of 60%

Operating speed 0.1 mm to 1 m/s (plunger models)

Operating frequency Mechanical: 600 operations/minute, max.

Electrical: 30 operations/minute, max.

Insulation resistance 100 MΩ min. (at 500 VDC)

Contact resistance 15 mΩ max.

Dielectric strength (see note 2) 1,000 VAC, 50/60 Hz for 1 min between terminals of the same polarity

V-21, V-16 and V-11:

2,000 VAC, 50/60 Hz for 1 min between current-carrying metal parts and ground, and between

each terminal and non-current-carrying metal parts

V-15 and V-10:

1,500 VAC, 50/60 Hz for 1 min between current-carrying metal parts and ground, and between

each terminal and non-current-carrying metal parts

Vibration resistance (see note 3) Malfunction: 10 to 55 Hz, 1.5-mm double amplitude

Shock resistance (see note 3) Destruction: 1,000 m/s2 (approx. 100G) max.

Malfunction: V-21/V-16/V-15: 300 m/s2 (approx. 30G) max.

V-11/V10: 200 m/s2 (approx. 20G) max.

Life expectancy Mechanical: 50,000,000 operations min. (60 operations/minute)

Electrical: V-21/V-16/V-15: 100,000 operations min. (30 operations/minute)

(V-15 heat resistive: 20,000 operations min. (30 ops/minute))

V-11/V-10: 300,000 operations min. (30 operations/minute)

(V-10 heat resistive: 50,000 operations min. (30 ops/minute))

Degree of protection IEC IP40

Degree of protection against electric shock Class I

Proof tracking index (PTI) 175

Ambient operating temperature

-25

C to 80

C (at 60% RH max.) with no icing

-25

C to 150

C for heat resistive models (at 60% RH max.) with no icing.

Ambient operating humidity 85% max. (for 5°C to 35°C)

Weight Approx. 6.2 g (plunger models)

Item V-21 V-16 V-15 V-11 V-10

Contact Specification Rivet

Material Silver alloy Silver

Gap

(standard value) 1 mm (F gap type) or 0.5 mm (G gap type)

Inrush current NC50 A max. 40 A max. 36 A max. 24 A max.

Minimum applicable load 160 mA at 5 VDC

Snap Action Switch V127

Engineering Data

■Contact Form

* The SPST-NC and SPST-NO contact form types listed in the

ordering information tables are for Pin Plunger models only.

For information concerning lever models consult Omron.

■Barrier direction (V-21 and V-16)

■Mounting Holes

All switches may be panel mounted using M3 mounting screws with

plane washers or spring washers to securely mount the switch.

Tighten the screws to a torque of 0.39 to 0.59 N·m.

■Mechanical service life ■Electrical service life

(Pin plunger models) (Pin plunger models)

V-21/-16/-15/-10

Number of operations (x10 )

200

100

0.01 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 (1.6) 1.8

Ambient temperature: 20±2°C

Ambient humidity: 65±5%

Without load

Operating frequency: 600 operations/min

V-10 (0.98 N {100 gf}),

V-11

V-10 (1.96 N

{200 gf})

V-15

V-16

V-21

OT rated value

Full stroke

OT (mm)

V-21/-16/-15

Operating frequency: 60 operations/min

cosφ = 1, 250 VAC

0.5

0.3

0.1

0 4 8 1216202428

V-21

V-15

V-16

Switching current (A)

Number of operations (x10 )

0.5

0.3

0.1

00.5 1 2 3 4 5 6 7 8 9 10 11 12

V-10

V-11

V-11/-10

Switching current (A)

Ambient temperature: 20±2°C

Ambient humidity: 65±5%

Operating frequency: 60 operations/min

cosφ = 1, 250 VAC

Number of operations (x10 )

Common

terminal

position

Contact form

SPDT SPST-NC* SPST-NO*

Bottom type

Side type

Right-hand Barrier Left-hand Barrier

Two, 3.1-dia. mounting holes or

M3 screw holes

10.3 ± 0.1

22.2 ±0.1

128Snap Action Switch V

Dimensions

■Terminals

Note: 1. Unless otherwise specified, all units are in millimeters and a tolerance of ±0.4 mm applies to all dimensions

2. The following table is for the SPDT contact specifications. Two terminals will be available for SPST-NO or SPST-NC contact specifications.

For terminal positions, refer to the above Contact Form

3. Right-angle PCB terminal type is available with some models (not shown). Drawings will be provided if requested.

D5: Pins at right angles, to the right

D6: Pins at right angle, to the left

Terminal type Solder Terminal

(A) Quick-connect Terminal

(#187) (C2) Quick-connect Terminal

(#250) (C)

COM

bottom position

COM

side position

Terminal

dimensions

t = 0.5

Three, solder terminals

(10)

2.9

(6.5)

(5.5)

t = 0.5

Three, quick-connect

terminals (#187)

(10)

2.9

(6.5)

(5.5)

t = 0.8

Three, quick-connect

terminals (#250)

(12.0)

3.2

(7.7)

(4.9)

(10)

2.4

(6.5)

(5.5)

(10)

2.4

(6.5)

(5.5)

(12.0)

3.6

(7.7)

(4.9)

1.6 dia.2.4 dia.

4.75±0.1

6.35

3.2 (see note)

Note: Indicates the length to the

center of the 1.6-dia. holes

1.6-dia. terminal hole

4.75±0.1

3.2

6.35

1.65-dia. terminal hole

6.35±0.1

3.95

8.1

Snap Action Switch V129

■Dimensions and Operating Characteristics

Thermoplastic Case Models

Note: 1. Unless otherwise specified, all units are in millimeters and a tolerance of ±0.4 mm applies to all dimensions

The following illustrations and drawings are for quick-connect terminals (#250) (terminals C). V models also incorporate terminals A and C2,

which are omitted from the following drawings. Refer to Terminals section for the dimensions of these terminals.

3. The @ in the model number is for the terminal code.

The illustrations for V-21, V-16 and V-11 show a hole size of 3.1 mm. V-21, V-16 and V-11 models with a suffix “K” have a hole size of 2.9 mm.

5. The operating characteristics are for operation in the A direction ( ).

Pin Plunger Models

➡

(Without Barrier)

V-21-1 6

V-16-1 5

V-11-1 4

3.1+0.13

–0.03 dia. holes

3.1+0.13

–0.03

3.4±0.15 dia. t=0.8

Three, quick-connect

terminals (#250)

20.2±0.25

2.8

1.6

2.8

10.3±0.1

22.2±0.1 2.8 (12.0)

27.8

39.8±0.8

2.8

8.4

15.9 19.1

0.6

4.2

2.8

10.3

(With Right-hand Barrier)

V-21-1 R6

V-16-1 R5

3.1+0.13

–0.03 dia. holes

3.1+0.13

–0.03

3.4±0.15 dia. t=0.8

Three, quick-connect

terminals (#250)

20.2±0.25

2.8 1.6

2.8

10.3±0.1

22.2±0.1 2.8 (12.0)

27.8

39.8±0.8

40.2

2.8

15.9

8.4 19.1

21.9

0.6 4.2 2.8

0.6

10.3

(With Left-hand Barrier)

V-21-1 L6

V-16-1 L5

3.1+0.13

–0.03 dia. holes

3.1+0.13

–0.03

3.4±0.15 dia.

t=0.8

Three, quick-connect

terminals (#250)

2.8 0.6

4.2

0.6

10.3

2.8

19.1

15.9

8.4

21.9

1.6

20.2±0.25

2.8 2.8

(12.0) 2.8

27.8

39.8±0.8

22.2±0.1

40.2

10.3±0.1

Characteristics V-21-1@6 V-16-1@5

OF max. 400 gf 200 gf

RF min. 80 gf 50 gf

PT max. 1.2 mm

OT min. 1.0 mm

MD max. 0.4 mm

OP 14.7 ± 0.4 mm

Characteristics V-11-1@4 V-11-1@5

OF max. 100 gf 200 gf

RF min. 20 gf 50 gf

PT max. 1.2 mm

OT min. 1.0 mm

MD max. 0.4 mm

OP 14.7 ± 0.4 mm

130 Snap Action Switch V

Note: 1. Unless otherwise specified, all units are in millimeters and a tolerance of ±0.4 mm applies to all dimensions

The following illustrations and drawings are for quick-connect terminals (#250) (terminals C). V models also incorporate terminals A and C2,

which are omitted from the following drawings. Refer to Te r m i n a l s section for the dimensions of these terminals.

3. The @ in the model number is for the terminal code.

The illustrations for V-21, V-16 and V-11 show a hole size of 3.1 mm. V-21, V-16 and V-11 models with a suffix “K” have a hole size of 2.9 mm.

5. The operating characteristics are for operation in the A direction ( ).

Short Hinge Lever Models

Hinge Lever Models

Long Hinge Lever Models

➡

V-211-1 6

V-161-1 5

V-111-1 43.1+0.13

–0.03 dia. holes

3.1+0.13

–0.03

3.4±0.15 dia.

t = 0.5

(see

note)

t=0.8

Three, quick-connect

terminals (#250)

22.1

8.1

2.8

10.3±0.1

2.8 (12.0)

27.8

22.2±0.1

39.8±0.8

1.6

2.8

8.4 15.9 19.1

0.6 2.8

4.3

10.3

Note: Stainless-steel lever

Characteristics V-211-1@6 V-161-1@5 V-111-1@4

OF max. 400 gf 200 gf 100 gf

RF min. 50 gf 50 gf 15 gf

PT max. 1.6 mm

OT min. 0.8 mm

MD max. 0.6 mm

OP 15.2 ± 0.5 mm

3.1+0.13

–0.03 dia. holes

3.1+0.13

–0.03

3.4±0.15 dia.

t = 0.5

(see note)

t=0.8

Three, quick-connect

terminals (#250)

35.6±0.8

8.1 1.6

2.8

10.3±0.1

22.2±0.1 (12.0)

2.8

27.8

39.8±0.8

2.8

15.9

8.4 19.1

0.6 2.8

4.3

10.3

V-212-1 6

V-162-1 5

V-112-1 4

Note: Stainless-steel lever

Characteristics V-212-1@6 V-162-1@5 V-112-1@4

OF max. 250 gf 125 gf 60 gf

RF min. 25 gf 14 gf 6 gf

PT max. 4.0 mm

OT min. 1.6 mm

MD max. 1.5 mm

OP 15.2 ± 1.2 mm

3.1+0.13

–0.03 dia. holes

3.1+0.13

–0.03

3.4±0.15 dia.

t = 0.5 (see note)

t=0.8

Three, quick-connect

terminals (#250)

59.4±0.8

2.8

10.3±0.1

22.2±0.1 (12.0)

2.8

27.8

39.8±0.8

2.8

8.4 15.9 19.1

0.6 2.8

4.3

10.3

V-213-1 6

V-163-1 5

V-113-1 4

Note: Stainless-steel lever

1.6

Characteristics V-213-1@6 V-163-1@5 V-113-1@4

OF max. 130 gf 70 gf 35 gf

RF min. 12 gf 6 gf - - -

PT max. 9.0 mm

OT min. 2.0 mm 3.2 mm

MD max. 2.8 mm

15.2

2.6 mm

15.2 mm

+2.6

−3.2

Snap Action Switch V131

Note: 1. Unless otherwise specified, all units are in millimeters and a tolerance of ±0.4 mm applies to all dimensions

The following illustrations and drawings are for quick-connect terminals (#250) (terminals C). V models also incorporate terminals A and C2,

which are omitted from the following drawings. Refer to Terminals section for the dimensions of these terminals.

3. The @ in the model number is for the terminal code.

The illustrations for V-21, V-16 and V-11 show a hole size of 3.1 mm. V-21, V-16 and V-11 models with a suffix “K” have a hole size of 2.9 mm.

5. The operating characteristics are for operation in the A direction ( ).

Simulated Roller Lever Models

Short Hinge Roller Lever Models

Hinge Roller Lever Models

➡

V-214-1 6

V-164-1 5

V-114-1 43.1+0.13

–0.03 dia. holes

3.1+0.13

–0.03

3.4±0.15 dia.

t = 0.5

(see note)

t=0.8

Three, quick-connect

terminals (#250)

3.5R

32.6±0.8

8.1 1.6

OP 2.8

10.3±0.1

22.2±0.1 (12.0)

2.8

27.8

39.8±0.8

0.6 3.48.2

10.3

Note: Stainless-steel lever

2.8

15.9 19.1

8.4

Characteristics V-214-1@6 V-164-1@5 V-114-1@4

OF max. 250 gf 125 gf 60 gf

RF min. 25 gf 14 gf 6 gf

PT max. 4.0 mm

OT min. 1.6 mm

MD max. 1.5 mm

OP 18.7 ± 1.2 mm

Note: 1. Stainless-steel lever

2. Oilless polyacetar resin roller

V-215-1 6

V-165-1 5

V-115-1 4

3.1

+0.13

–0.03

dia. holes

3.1

+0.13

–0.03

3.4±0.15 dia.

t = 0.5

(see

note 1) 4.8 dia. × 4.8

(see note 2)

t=0.8

Three, quick-connect

terminals (#250)

20.1

8.1 1.6

2.8

10.3±0.1

22.2±0.1 2.8 (12.0)

27.8

39.8±0.8

2.8

8.4 15.9 19.1

0.6 5.1

10.3

Characteristics V-215-1@6 V-165-1@5 V-115-1@4

OF max. 480 gf 240 gf 120 gf

RF min. 50 gf 50 gf 15 gf

PT max. 1.6 mm

OT min. 0.8 mm

MD max. 0.6 mm

OP 20.7 ± 0.6 mm

V-216-1 6

V-166-1 5

V-116-1 43.1 +0.13

–0.03 dia. holes

3.1+0.13

–0.03

3.4±0.15 dia.

t = 0.5

(see note 1) 4.8 dia. × 4.8

(see note 2)

t=0.8

Three, quick-connect

terminals (#250)

34.0±0.8

8.1 1.6PT

OP 2.8

10.3±0.1

22.2±0.1 (12.0)

2.8

27.8

39.8±0.8

2.8

19.1

0.6

5.1

10.3

15.9

8.4

Note: 1. Stainless-steel lever

2. Oilless polyacetar resin roller

Characteristics V-216-1@6 V-166-1@5 V-116-1@4

OF max. 250 gf 125 gf 60 gf

RF min. 25 gf 14 gf 6 gf

PT max. 4.0 mm

OT min. 1.6 mm

MD max. 1.5 mm

OP 20.7 ± 1.2 mm

132 Snap Action Switch V

Thermosetting Case Models

Note: 1. Unless otherwise specified, all units are in millimeters and a tolerance of ±0.4 mm applies to all dimensions

The following illustrations are for quick-connect terminals (#250) (terminals C). Refer to Terminals section for the dimensions of other terminals.

3. The @ in the model number is for the terminal code.

The illustrations show models with a suffix “K”, which have a hole size of 2.9 mm. Omit the “K” to obtain models with hole size = 3.1 mm.

5. The operating characteristics are for operation in the A direction ( ).

Pin Plunger Models

Short Hinge Lever Models

Hinge Lever Models

Long Hinge Lever Models

➡

V-15G-1 5-K

V-10G-1 5-K

V-10G-1 4-K

2.9

+0.13

–0.03

dia. holes

3.1

+0.13

–0.03

3.4±0.15 dia.

t=0.5

Three, solder

terminals

20.2±0.25

2.8

10.3±0.1

22.2±0.1 2.8

27.8 (10)

37.8±0.8

15.9 18.8

4.2 2.8

10.3

Characteristics V-15G-1@5-K

V-10G-1@5-K V-10G-1@4-K

OF max. 200 gf 100 gf

RF min. 50 gf 20 gf

PT max. 1.2 mm

OT min. 1.3 mm

MD max. 0.3 mm

OP 14.7 ± 0.4 mm

V-15G1-1 5-K

V-10G1-1 5-K

V-10G1-1 4-K

2.9

+0.13

–0.03

dia. holes

3.1

+0.13

–0.03

3.4±0.15 dia.

t = 0.5 (see note)

t=0.5

Three, solder terminals

22.1

8.1

2.8

22.2±0.1 2.8

27.8 (10)

37.8±0.8

15.9 18.8

4.3 2.8

10.3

OP 10.3±0.1

Note: Stainless-steel lever

Characteristics V-15G1-1@5-K

V-10G1-1@5-K V-10G1-1@4-K

OF max. 200 gf 100 gf

RF min. 50 gf 15 gf

PT max. 1.5 mm

OT min. 1.0 mm

MD max. 0.5 mm

OP 15.2 ± 0.5 mm

V-15G2-1 5-K

V-10G2-1 5-K

V-10G2-1 4-K 2.9+0.13

–0.03 dia. holes

3.1+0.13

–0.03

3.4±0.15 dia.

t = 0.5 (see note)

t=0.5

Three, solder terminals

35.6±0.8

8.1

2.8

10.3±0.1

22.2±0.1 2.8

27.8

(10)

37.8±0.8

15.9 18.8

4.3 2.8

10.3

Note: Stainless-steel lever

Characteristics V-15G2-1@5-K

V-10G2-1@5-K V-10G2-1@4-K

OF max. 125 gf 60 gf

RF min. 14 gf 6 gf

PT max. 3.3 mm

OT min. 2.3 mm

MD max. 0.8 mm

OP 15.2 ± 1.2 mm

15.2 mm

+2.6

−3.2

V-15G3-1 5-K

V-10G3-1 5-K

V-10G3-1 4-K

2.9

+0.13

–0.03

dia. holes

3.1

+0.13

–0.03

3.4±0.15 dia.

t = 0.5 (see note)

t=0.5

Three, solder terminals

22.2±0.1

27.8

2.8

(10)

15.9 18.8

10.3±0.1

8.1

4.3

2.8

10.3

37.8±0.8

59.4±0.8

2.8

Note: Stainless-steel lever

Characteristics V-15G3-1@5-K

V-10G3-1@5-K V-10G3-1@4-K

OF max. 70 gf 35 gf

RF min. 6 gf - - - gf

PT max. 9.0 mm 7.6 mm

OT min. 3.0 mm 3.2 mm

MD max. 2.0 mm

OP 15.2 ± 2.6 mm

Snap Action Switch V133

Note: 1. Unless otherwise specified, all units are in millimeters and a tolerance of ±0.4 mm applies to all dimensions

The following illustrations are for quick-connect terminals (#250) (terminals C). Refer to Te r m i n a l s section for the dimensions of other terminals.

3. The @ in the model number is for the terminal code.

The illustrations show models with a suffix “K”, which have a hole size of 2.9 mm. Omit the “K” to obtain models with hole size = 3.1 mm.

5. The operating characteristics are for operation in the A direction ( ).

Simulated Roller Lever Models

Short Hinge Roller Lever Models

Hinge Roller Lever Models

Accessories

Refer to the “V/VX/D3C Common Accessories” datasheet for information regarding VAL, VAM and VAV external actuators (sold separately).

➡

V-15G4-1 5-K

V-10G4-1 5-K

V-10G4-1 4-K

3.5R

2.9+0.13

–0.03 dia. holes

3.1+0.13

–0.03

3.4±0.15 dia.

t = 0.5 (see note)

t=0.5

Three, solder terminals

22.2±0.1

27.8

2.8

(10)

15.9 18.8

10.3±0.1

8.1

4.3

2.8

10.3

37.8±0.8

32.6±0.8

2.8

Note: Stainless-steel lever

Characteristics V-15G4-1@5-K

V-10G4-1@5-K V-10G4-1@4-K

OF max. 125 gf 60 gf

RF min. 14 gf 6 gf

PT max. 3.3 mm

OT min. 2.3 mm

MD max. 0.8 mm

OP 18.7 ± 1.2 mm

4.8 dia. × 4.8 (see note 2)

2.9+0.13

–0.03 dia. holes

3.1+0.13

–0.03

3.4±0.15 dia.

t = 0.5 (see note 1)

22.2±0.1

27.8

2.8

(10)

15.9 18.8

10.3±0.1

8.1

5.1

10.3

37.8±0.8

20.1

2.8

V-15G5-1 5-K

V-10G5-1 5-K

V-10G5-1 4-K

Note: 1. Stainless-steel lever

2. Oilless polyacetar resin roller

t=0.5

Three, solder terminals

Characteristics V-15G5-1@5-K

V-10G5-1@5-K V-10G5-1@4-K

OF max. 240 gf 120 gf

RF min. 50 gf 15 gf

PT max. 1.5 mm

OT min. 1.0 mm

MD max. 0.5 mm

OP 20.7 ± 0.6 mm

V-15G6-1 5-K

V-10G6-1 5-K

V-10G6-1 4-K

4.8 dia. × 4.8 (see note 2)

2.9

+0.13

–0.03

dia. holes

3.1

+0.13

–0.03

3.4±0.15 dia.

t = 0.5 (see note 1)

22.2±0.1

27.8

2.8

(10)

15.9 18.8

10.3±0.1

8.1

5.1

10.3

37.8±0.8

34.0±0.8

2.8

Note: 1. Stainless-steel lever

2. Oilless polyacetar resin roller

t=0.5

Three, solder terminals

Characteristics V-15G6-1@5-K

V-10G6-1@5-K V-10G6-1@4-K

OF max. 125 gf 60 gf

RF min. 14 gf 6 gf

PT max. 3.3 mm

OT min. 2.3 mm

MD max. 0.8 mm

OP 20.7 ± 1.6 mm

134 Snap Action Switch V

Precautions

Be sure to read the precautions and information common to all Snap Action and Detection Switches, contained in the Technical User’s Guide,

“Snap Action Switches, Technical Information” for correct use.

■Correct Use

Terminal Connection

To solder the lead to the solder terminal, apply a soldering iron rated

at 60 W max. quickly (within 5 seconds) with the actuator at the free

position.

Note that applying a soldering iron for too long a time or using one

that is rated at more than 60 W may degrade the switch characteris-

tics.

Use an appropriate mating connector for #187 or #250 quick connect

terminals.

Specifications Approved by TÜV Rheinland

According to EN61058-1

Appropriate Cable Size (mm2)

Operation

Make sure that the operating body pushes the switch actuator with

an adequate force when the switch is to be operated, and that it does

not touch the actuator when the switch is released.

Do not change the operating position by modifying the actuator.

Do not use the switch in a application where the operating speed is

extremely slow or the actuator is set in the midpoint between the free

position and operating position.

Install the pin plunger switch so that the operating force is applied in

alignment with the stroke of the actuator. The switch should be set so

that its stroke is in the range of 60 to 90% of the rated OT (minimum

value) when the switch has been operated.

■Cautions

Insulation Distance

According to EN61058-1, the minimum insulation thickness for this

switch should be 1.1 mm and minimum clearance distance between

the terminal and mounting plate should be 1.0 mm. If the insulation

distance cannot be provided in the product incorporating the switch,

either use a switch with insulation barrier or use a separator to

ensure sufficient insulation distance.

Model Solder terminal

V-10 0.75, 1.25, 2.0

V-15 1.25, 2.0

Snap Action Switch V

MEMO

Snap Action Switch V

OMRON ON-LINE

Global - http://www.omron.com

USA - http://www.components.omron.com

Cat. No. X303-E-1 Printed in USA

OMRON ELECTRONIC

COMPONENTS LLC

55 E. Commerce Drive, Suite B

Schaumburg, IL 60173

847-882-2288

11/10 Specifications subject to change without notice

All sales are subject to Omron Electronic Components LLC standard terms and conditions of sale, which

can be found at http://www.components.omron.com/components/web/webfiles.nsf/sales_terms.html

ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.

To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.

Mouser Electronics
  
Authorized Distributor
 
  
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
 
 
 
 Omron:   
  V-15G-1C25-K  V-15G-1C26-K  V-10-7A5  V-10G5-1C25-K  V-15G5-1C25-K  V-15G5-1C26-K  V-10G3-1C24-K  V-
15G3-1C26-K  V-15G3-1C25-K  V-10G-1A4K  V-15G6-1C26-K  V-15G6-1C25-K  V-15G4-1C25-K  V-10G-1C24-K  V-
15-1A5  V-15G2-1C25-K  V-10G2-1C24-K  V-15G2-1C26-K  V-10G2-1C25-K  V-15-1B5  V-16G-3C26  V-215-1CR6  V-
15G-2C26-K  V-15G-1C5-K  V-15G-1B5-K  V-15G-1E5-K  V-15G-2C25-K  V-15G-3A5-K  V-15G-3C25-K  V-15G-3C5-K
  V-15G-4A5-K  V-15G-6A5-K  V-15G1-1C25-K  V-15G1-1E5-K  V-15G2-1A5-K  V-15G2-1E5-K  V-15G3-1A5-K  V-
15G3-1B5-K  V-15G4-1A5-K  V-15G5-1A5-K  V-15G5-1B5-K  V-15G6-1A5-K  V-15G6-1B5-K  V-10G-1A5-K  V-10G-
1B5-K  V-10G-2C25-K  V-10G-3C25-K  V-10G1-1C25-K  V-10G2-1A5-K  V-10G3-1C25-K  V-10G4-1C25-K  V-10G5-
1A5-K  V-10G5-1B5-K  V-10G6-1A5-K  V-10G-1B4-K  V-10G-1E4-K  V-10G-2C24-K  V-10G-3C24-K  V-10G-4A4-K  V-
10G1-1A4-K  V-10G1-1C24-K  V-10G1-1E4-K  V-10G2-1A4-K  V-10G2-1B4-K  V-10G3-1A4-K  V-10G4-1A4-K  V-10G4-
1C24-K  V-10G4-1B4-K  V-10G5-1A4-K  V-10G5-1B4-K  V-10G6-1A4-K  V-10G6-1B4-K  V-15-3B6-K  V-01G-1C23-K 
V151C5  V-16G-3C25-L  V-11-1B5  V-16G88K-3CR5  V-15-3C6-K  V-15-1A6  V-16G-3C25  V-16G-3C25-K  V-10G-
1C25-K  V-10G5-1C24-K  V-10G6-1C24-K  V-15G-1A5-K  V-15-2C26-K  V-15G-1B6-K  V-10-1A4  V-10-1A4-T  V-10-
1B4  V-10-1B5  V-10-1C25  V-10-1C25-K  V-10-1E25  V-102-1A4  V-102-1A4-T  V-103-1A4  V-103-1C24-T  V-103-
1C25-T